foo2hiperc-wrapper Man page

foo2hiperc-wrapper General Commands Manual foo2hiperc-wrapper


foo2hiperc-wrapper – Convert Postscript into a HIPERC printer stream


foo2hiperc-wrapper [options] [ps-file]


foo2hiperc-wrapper is a Foomatic compatible printer wrapper for the
foo2hiperc printer driver. This script reads a Postscript ps-file or
standard input and converts it to the Oki HIPERC printer format for
driving the Oki C310dn, C3100, C3200, C3300n, C3400n, C5100n, C5500n,
C5600n and the C5800n HIPERC printers.

This script can be used in a standalone fashion, but is intended to be
called from a printer spooler system which uses the Foomatic printer



Normal Options
These are the options used to select the parameters of a print job that
are usually controlled on a per job basis.

-c Print in color (else monochrome).

-C colormode
Color correction mode [0].

10 ICM color profile (using -G *.icm file)

-d duplex
Duplex code to send to printer [1].
│ │ │
│1 off │ 2 long edge │ 3 short edge

-m media
Media code to send to printer [0].

plain 0
labels 1
transparency 2

-p paper
Paper size code to send to printer [2].

│ 1 A4 │ 2 letter │
│ 3 legal │ – – │
│ 5 A5 │ 6 B5jis │
│ 7 A6 │ 8 env Monarch │
│ 9 env DL │ 10 env C5 │
│11 env #10 │ 12 executive │
│13 env #9 │ 14 legal 13.5″ │
│15 A3 │ 16 tabloid/ledger │
-n copies
Number of copies [1].

-r xresxyres
Set device resolution in pixels/inch [600×600].

-s source
Source (Input Slot) code to send to printer [0].
│ │
│0 auto select │
│1 tray1 │ 2 tray2
│3 multi │ 4 manual

-t Draft mode. Every other pixel is white.

-2 -3 -4 -5 -6 -8 -9 -10 -12 -14 -15 -16 -18
Print in N-up. Requires the psutils package.

-o orient
Orientation used for N-up.

Portrait -op (normal)
Landscape -ol (rotated 90 degrees anticlockwise)
Seascape -os (rotated 90 degrees clockwise)

Printer Tweaking Options
These are the options used to customize the operation of foo2hiperc for
a particular printer.

-u xoffxyoff
Set the offset of the start of the printable region from the
upper left corner, in pixels [varies with paper size].

-l xoffxyoff
Set the offset of the end of the printable region from the lower
right corner, in pixels [varies with paper size].

-L mask
Send the logical clipping values from -u/-l in the HIPERC
stream. foo2hiperc-wrapper always runs Ghostscript with the
ideal page dimensions, so that the scale of the image is cor‐
rect, regardless whether or not the printer has unprintable
regions. This option is used to move the position of the
clipped image back to where it belongs on the page. The default
is to send the amount which was clipped by -u and -l, and should
be good in most cases.

0 don’t send any logical clipping amounts
1 only send Y clipping amount
2 only send X clipping amount
3 send both X and Y clipping amounts

-z model
Model is 0 for non-A3 sized printers, and 1 for
A3/Tabloid/Ledger sized printers (i.e. C810, etc.). The default
is 0.

-Z compressed
Use uncompressed (0) or compressed (1) JBIG data.

Color Tweaking Options
These are the options used to control the quality of color output.
Color correction is currently a WORK IN PROGRESS.

-g gsopts
Additional options to pass to Ghostscript, such as
-g“-dDITHERPPI=nnn”, etc. This option may appear more than

-G profile.icm
Convert profile.icm to a Postscript color rendering dictionary
(CRD) using foo2zjs-icc2ps and adjust the printer colors by
using the Postscript setcolorrendering operator. (WORK IN

Prepend to the Postscript input to perform color
correction using the setcolortransfer Postscript operator. For
example, the file might contain:
{0.333 exp} {0.333 exp} {0.333 exp} {0.333 exp} setcolortransfer

-I intent
Select profile intent from the ICM file. 0=Perceptual, 1=Col‐
orimetric, 2=Saturation, 3=Absolute. Default is 0 (perceptual).

Debugging Options
These options are used for debugging foo2hiperc and its wrapper.

-S plane
Output just a single color plane from a color print and print it
on the black plane. The default is to output all color planes.

1 Cyan
2 Magenta
3 Yellow
4 Black

-D level
Set Debug level [0].

Create a monochrome HIPERC stream from a Postscript document, examine
it, and then print it using nc or netcat:

foo2hiperc-wrapper > testpage.hc
hipercdecode < testpage.hc nc 192.168.1.NNN 9100 < testpage.hc Create a color HIPERC stream from a Postscript document: foo2hiperc-wrapper -c > testpage.hc



foo2hiperc, hipercdecode


Rick Richardson